Tap Installation Chatham | Professional Fitting

Name: Chatham Plumbing Services
Address: Chatham, Kent, ME4 4TR, GB
Telephone: 01634 123456

Installing a new tap looks simple, but it needs doing properly to avoid leaks. You need to connect hot and cold supplies, seal the base, and tighten the backnut without cracking the sink. Get it wrong and you'll flood the place.

We'll fit your new tap (kitchen, bathroom, basin, whatever), connect the supplies, test for leaks, and tidy up. Takes about an hour for a straightforward tap. If your pipes are awkward or the tap needs adaptors, it might take longer.

There's no call-out fee when you book with us. Bring your own tap or we can supply one. We'll quote you before we start, and our 12-month guarantee is included with our membership plan.

What to Check Before Buying a Tap

Number of tap holes

Count the holes in your sink or basin. One hole = monobloc mixer. Two holes = pillar taps or two-hole mixer. Three holes = bridge mixer. Buy the wrong type and it won't fit.

Tap tail length

The threaded tails need to be long enough to reach through the sink and stick out far enough to attach fittings. Standard tails are fine for most sinks. Thick worktops or deep basins might need extended tails.

Water pressure requirements

Some taps need minimum pressure. If you've got low pressure (loft tank, no pump), check the tap's minimum pressure rating before you buy.

How We Fit Taps

1

Turn off the water

We'll turn off hot and cold supplies using isolation valves or the main stop cock.

2

Remove the old tap

We'll disconnect the supplies, undo the backnut, and lift the old tap out. We'll clean the sink around the tap hole.

3

Fit the new tap

We'll feed the tails through, fit the gasket, and tighten the backnut. We'll make sure it's aligned straight and not over-tightened.

4

Connect the supplies and test

We'll connect hot and cold feeds using flexible hoses or copper pipe. We'll turn the water on and check for leaks.

Tap Installation in Chatham Homes

Victorian tap holes

Older sinks often have separate hot and cold taps. We can fit a monoblock mixer tap using a blanking plate to cover one hole.

Worktop thickness

Modern thick stone worktops need longer tap tails. We check before fitting and supply extended connectors if needed.

Flexible vs rigid pipes

Flexible hoses are easier to fit and handle movement better. Rigid copper looks neater but less forgiving if alignment isn't perfect.

Water pressure for tap choice

Low pressure needs taps rated for it. High pressure systems can use any tap but may benefit from flow restrictors to reduce splashing.

Tap Installation Pricing

Upfront prices, no nasty surprises

We'll always tell you the cost before we start. These are typical price ranges, your exact quote depends on the job.

Service	Typical Cost
Tap installation (standard)	£70 – £130
Tap installation (awkward access)	£100 – £180

All prices are estimated. Final costs depend on the specific job. We provide detailed quotes before starting work.

Common Questions

Got questions? Here's the quick answers.

How much does tap installation cost in Chatham?

Standard tap fitting costs £70 to £130. Awkward access costs £100 to £180. We'll quote you before we start.

How long does it take?

About 30 minutes to an hour for a straightforward tap.

Can I supply my own tap for installation?

Yes. Just make sure it's the right type for your sink and pressure.

Will you supply the tap?

Yes. We'll source a decent mid-range tap and fit it. We'll quote you for tap and fitting together.

What if my pipes don't reach?

We'll extend them using flexible hoses or copper pipe.

Are isolation valves required for tap installation?

It's a good idea. We can fit them while we're there. Adds about £30-£50.

Will you dispose of my old tap?

Yes, if you want. We'll dispose of it.

Do you install taps bought from online retailers?

Yes, as long as it's a proper tap and the right type for your sink.

Back to General Plumbing

Get In Touch

Request a free quote

Tell us what you need and we'll get back to you with a no-obligation quote, usually within the hour during working hours.

01634 123456

Mon–Thurs 8.30am–6pm, Fri 9am–4pm

Covering all Chatham postcodes

Tap installation across Chatham